#Gentoo Handbook Install Gentoo Linux#
#Gentoo Handbook Mac OS X#
#Gentoo Handbook Download Page Offers#

Gentoo Handbook Download Page Offers

Gentoo Handbook Install Gentoo Linux

The installations will differ slightly for other computer architectures (such as ARM or PowerPC), but the objectives of each step are the same.GentooвЂ™s download page offers a mimimal installation CD and a hybrid ISO which contains a graphical live Linux environment. You are welcome to add and edit wiki articles - be bold: Start a new wiki article to document a new subject, knowledge or package.The point of the Handbook is to get a bare-bones Gentoo system up and running, not to cover all possible installation paths irregular partitioning, init systems.This Instructable will walk through the steps to install Gentoo Linux on an AMD64 machine from the official Gentoo Installation CD. IRC channels such as gentoo-kde , gentoo , and gentoo-desktop Mailing lists such as gentoo-user and gentoo-desktop. Gentoo Forums, usually the Desktop Environments forum.

There are many good docs and guides hereBy the end of this Instructable, you will have a fully configured Gentoo system installed on your machine's hard drive, with a boot loader.There are some steps to take before starting this installation guide. Configure your network the way I suggested, get your system logger started. Please continue using the Gentoo Handbook. You can now configure your running system. The installation is instead done by following a step by step handbook and it is time-consuming and not very friendly.Now that you are in you newly inatalled Gentoo system, you should not need the CD again.

In order to not mistakenly use a different hard drive, that contains data you want to keep, it is a good idea to disconnect all other drives from your machine during the Gentoo installation.The exact steps for installing Gentoo may differ between versions of the installation medium, or depending on the machine. This step will erase all other data on the drive, so make sure that you have a free hard drive that you are willing to use. Finally you will be formatting a hard drive during the installation. Next, establish a wired ethernet connection to your network by plugging an ethernet cable directly from your network router or switch to your machine's ethernet port. Do some research about your system.

Gentoo Handbook Mac OS X

Iso and the location of your USB device:Dd if=./install-amd64-minimal-XXXXXXXX.iso of=/dev/sdXBE EXTREMELY CAREFUL WHILE RUNNING dd. Iso image to, then execute, replacing the X's to correctly name the. Iso image, in the terminal, you must navigate to the directory which you downloaded the. If you are running Windows or Mac OS X, or another operating system, search for a tutorial about mounting a bootable ISO to a USB drive or CD.To create a bootable USB flash drive from the. This process may be different for different operating systems.

This will prevent you from accidentally overwriting data that you want to keep. Now is the time to disconnect all hard drives from your machine and only connect the hard drive you wish to install Gentoo on. Iso file.Once the bootable USB flash drive or CD is created, you must restart your computer. Double check that the device you provide after 'of=' is the correct device you want to mount the.

If you miss your opportunity, you can always power off the computer and power it back on. Quickly tap this key before the screen changes. This key is usually ESC, DEL, or F1 but will vary, depending on your motherboard.

Press ENTER, which should select the default option of booting the Gentoo Live Image. The computer may beep, and you may see another menu asking what Operating System to boot. Select this, and the Gentoo Installation Image should begin booting on your computer.

Look for a device named 'eth0', 'eno0', 'ens1', 'enp5s0', or something similarly named. To find out type the following command at your terminal and press enter:This command should produce a list of the network devices on your machine. This may automatically establish a connection, but it might not. Plug an ethernet cable from your computer's ethernet port to your network router or switch. The easiest method to establish an internet connection is to directly connect with an ethernet cable. The installation medium should automatically detect your device hardware and start the drivers for your network cards.

Network connection can range from a very easy step that automatically works, to a difficult step requiring time to configure the connection correctly. Once this is complete, try running again:For any trouble connecting to your network, refer to the Gentoo Handbook. If your network is specially configured and has special needs to establish an internet connection (such as the use of proxies or PPPoE, or to connect over wireless, refer to the Gentoo Handbook at for instructions). Configure the set up to the best of your knowledge. If you do not see this, try running on the terminal:This will bring up an interactive menu that will walk you through a network setup. If you see this, your network device has been given an IP address and should be connected to your network.

Make sure that you do not use a hard drive with information that you want to keep. If you do not receive any bytes back, make sure that your network router or switch is properly connected to the internet.Once you are able to connect to the internet, you can next move on to acquiring more installation materials.During this step, you will partition and format a hard drive in preparation to house your Gentoo system. If you are receiving data back, press CTRL+C (holding the CTRL key and tapping C), to cancel the ping.

There are many different set-ups for your drive, that you may want to choose if you are experienced with Linux. We are going to use a MBR (Master Boot Record) and create 3 basic partitions, the boot partition, a swap partition, and a root partition. Each distinct letter following 'sd' is associated with a different physical drive, and each number following this is a different partition.We now want to partition the disk to prepare for the Gentoo system. Typically, your hard drives will appear as devices that start with 'sd', although older systems may use other letters, such as 'hda'. The devices you want to look at will be be labelled 'sd*' and 'sd*#', such as 'sda' or 'sda1'. Make sure the drive that you want to use is at least 24Gb in size.To see the list of devices, run at the terminal:This will show a long list of devices, most of which you can ignore.

Type 'p' and then ENTER, to print out the list of partitions on the drive. Start this program by running in your terminal (replacing /dev/sda with the location of your device):This program will give you a prompt. We will not cover these set-ups in this Instructable.To partition the disk, we are going to use a program called fdisk.

Then 'p' for a primary partition. Create the partition by entering 'n', for a new partition. This partition is where our boot loader, which the BIOS uses to load the operating system, will reside. When entering 'p' gives an empty list, the disk is clear of all partitions.Now we want to create the first of our three partitions, the boot partition. Repeat this until all partitions are deleted.

It will also be used when the computer hibernates, or crashes. The swap partition is used by the Operating System to store temporary files it needs to run properly. This will set the 'bootable' flag for this partition, which tells the machine which partition to boot.Now we will make the swap partition. What we have just done is created a new partition, numbered 1, that is located at the first open sector on the disk and is of length 256Mb. Then enter '+256M' for the last sector. When asked for the first sector, hit enter to choose the default.

Create this partition by entering 'n', then '3', then hit enter twice. This is where the Gentoo system and all of your data will be stored. This will set the type of the partition to Linux Swap.Finally, we will create the root partition. Hit enter when asked for the first sector again, then '+#G', replacing the # with the number of Gb you want the swap partition to be. Create another partition by entering 'n', then enter '2'.